Tweet
ok ok.... does anyone have a good article or site that describes the reconstitution process for igf?? i have read way to many conflicting methods. I have both AA and sterile water. I'm going to use the AA for recon then the water for my injections?? right?
-
I'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy! -
Re: IGF recon....
aa(solution) is to mix it wt igf1 and sterile water is to cut the pain down..Originally posted by mick10-07
do u have 2 cc of aa and 10 ml of sterile water? -
Re: IGF recon....
yeh...well...i think. I have 10ml viles of AA and 10ml plastic viles of water. my guys on vacation so i dont really know what the strength of my igf is. I got 50 viles with powder igf and 5 10ml viles of AA. Can someone please tell me what the dose would be from this info i gave.....I'm so confusedI'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy!Comment
-
Re: IGF recon....
-----------------------------------------------
first remove the vacuum from the vial, by injecting air into it. when the vacuum is gone it will no longer pull the plunger down. if there is no vacuum, don't worry about it.
you can use as much AA as you like. the original kits came with 1ml. most time when i drew it into a syringe, it was't even that much, which of course is a problem. chemone includes a little more than 2ml so if you want to use 1ml, fine, 2ml, fine. there will be enough.
i personally use 2ml because it is easier to measure later when you draw it into a syring.
after removing the vacuum SLOWLY add AA to the vial. try not to let the stream of aa hit the powder directly, try to let it run down the glass into the powder. when the aa is in gently swirl the vial until all is disolved. do not shake.
a 1ml syringe is marked like this llll10llll20llll30llll40llll50llll60...etc
a 1/2 ml syringe is like this llll5llll10llll15llll20llll25llll30
on a 1ml each line represents 2 units 2,4,6,8,10
on a 1/2 ml each line is 1 unit 1,2,3,4,5,6,7,8,9,10. this makes it easier to measure.
so if you use 1ml of aa, on a 1ml pin, each line is 20mcg. on a 1/2ml pin each line is 10mcg
if you use 2ml of aa, on a 1ml pin each line is 10mcg, on a 1/2 ml each line is 5mcg...the 5line is 25mcg, 10 line is 50mcg...etc
so you see that the easiest way to measure is using 2ml and a 1/2ml pin
your igf is stored in aa solution, nacl is added to dilute at the time of injection. draw twice as much nacl as igf. so if you draw igf to the ten line, draw nacl to the 30 line and you are ready to go.
normally i do this by PM where i can answer individual questions. in a post i tried to cover every possibility, making this the most complete and possibly most confusing version yet....sorry about that.
feel free to post your questions, i probably deserve it...lol
chemone's kits are exactly how they should be. a true .6% aa solution and nacl(saline solution) to dilute. diluting lessens the sting from the acid and prevents tissue necrosis.
CComment
-
Re: IGF recon....
ok...here's what i did. In total i ordered 5 mg of igf. it came in 50 small viles along with 5 10ml viles of AA. Givin these numbers I'm assuming that one of those viles when reconstituted contains 100mcg of IGF right?? I used a 25 gauge 3ml needle to add the AA to the small igf vile....added 1 cc or 1 ml.....when i do my shots i'm drawing about 33mcg's per shot then back loading with a little water..... it just doesn't seem like i'm diong this right, or that i have the strength of the igf wrong.....
what do you think?I'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy!Comment
-
Re: IGF recon....
bump for chaosComment
-
Re: IGF recon....
it sound like you have it right. the igtropin kits are 10 100mcg vials. so if you add 1ml to thim you have roughly 1ml at 100mcg/ml so every 5 on 10 on the pin is 10mcg.
using a 3ml pin, i would load the water first to help minimize igf loss.Comment
-
Re: IGF recon....
ok perfect.....now for my next question. My shipper sent the dry powder in a cold pack, this is good. but i've been hearing that some guys don't even refridgerate their IGF at all. Can you please tell me if the reconed IGF has to be kept cold. And....is it best to recon all my viles at one time or what??
you think 7 years of doing cycles would keep you up to date on all this new IGF stuff.........I'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy!Comment
-
Re: IGF recon....
yes it has to be in teh fridge an cold broComment
-
Re: IGF recon....
crap!! i've been keeping it in my closet.....i dont know if i have access to a fridge if you know what i mean. (wife)
I'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy!Comment
-
Re: IGF recon....
if u didnt mix it, its ok, but if u mixed it, u have to put it in fridge mick10Originally posted by mick10-07crap!! i've been keeping it in my closet.....i dont know if i have access to a fridge if you know what i mean. (wife)Comment
-
Re: IGF recon....
actually reconstituted in AA it will last 2 years at room temp. .... longer than in powder form,BUT i would refridgerate to be safe.Comment
-
Re: IGF recon....
^^damn, thats a long ass time for a peptide.- TestifyHey, I never saw a skinny bodybuilder before - eat away!
- 02THE BEST WAY TO GET OVER A GIRL IS TO GET UNDER ANOTHER ONE
Comment
-
Re: IGF recon....
yeh, i did read that somewhere, thats why i'm asking to be sure. I'll still have to find a way to keep it cold. maybe i'll just move to the north pole so i can keep it in a tree or something...........
thanks for clearing this stuff up guys!I'm a Muscle Farmer....This years Crop is gunna be awesome.
Gyno is sexy!Comment
-
Re: IGF recon....
i thought the igtorpin by gen lei is mixed wt bac water and NOT aa...is taht what mick10 has?????Originally posted by chaosComment
Comment