Am i retarded abotu warming up my oil?

[prolangtum]

I always put a cup in the microwave, warmed the water for a minute, then stuck the tightly capped pin in the water for 30 seconds or so, to make the oil thinner. Today, it seemd like I had a revelation or something, and stuck it inside a plastic baggie, then in the cup of water. No matter how hard i screwed the cap on before, I always compromised a bit of sterility, soem water always got through. Please tell me Im not the only one who used to do it that way.

[CJWolf]

i do it that way sometimes ... i change the needle after i do that though, so i don't get any water into the syringe/needle that i use.

[prolangtum]

I just felt like i discovered electricity or something, I was amazed at my prior stupidity.

[BigD]

I run the capped syringe under hot water, but I make sure never to let the water touch the cap itself, I keep it flowing over the barrel of the syringe. So far, I've never had any probs, and I can get any oil I want through I 28g slin pin

[L.C.]

I warm the loaded syringe (w/o needle) in the microwave for 8-10 seconds.

[DickRenegade]

?

purpose?

are you warming the oil to make it easier to go through the pin or for sterility?

just wondering. i've never heated mine. if you're just warming it up a bit thinking it won't make it as sore after i think you're mistaken.

dick

[BigD]

Just to make the oil thinner, so it flows faster. Not to kill pain, I know it won't do that, but even 1cc can take a while through the 28g pins I use, unless I warm it up... then it's quick and painless

[GSU7]

The best thing to do imo is to heat bowl of water and put the vial/amp in the water and then into the syringe that way sterility is not compromised. Just my .02.

[gonzaox]

Best thing to do is shoot it the way it is. Why change the course of things. We look for way to many commodities. So it goes slow...use a lower gauge pin, so it hurts....so what! my .02

[AustinTX]

Originally posted by GSU7
The best thing to do imo is to heat bowl of water and put the vial/amp in the water and then into the syringe that way sterility is not compromised. Just my .02.

We have a winner....

[MidnightRider]

I warm the vial in water before loading. It is easier to push through a 25 pin warm.

[johnnyboy845]

Originally posted by BigD
I run the capped syringe under hot water, but I make sure never to let the water touch the cap itself, I keep it flowing over the barrel of the syringe. So far, I've never had any probs, and I can get any oil I want through I 28g slin pin

thats exactly what I do also... and a few times taking a shot forgot to warm it under the water and there was a little bit more pain the next day at injection site and oil is definately harder to push through the pin when cold

[GSU7]

The only juice ive ever done this with is t400...try pulling that out w/a 25g pin it takes for damn ever. Heating it up a bit seemed to help.

[god smacked]

I've always loaded my dart and then hold up a hair dryer to the barrel of the dart. Thing gets really hot if you're not careful.

I have yet to have any problems.

[jjgarcia3]

Re: ?

Originally posted by DickRenegade
purpose?

are you warming the oil to make it easier to go through the pin or for sterility?

just wondering. i've never heated mine. if you're just warming it up a bit thinking it won't make it as sore after i think you're mistaken.

dick

it kills the soreness for me, ive tried both ways, heating and not heating and when i do heat it cuts the soreness in half. lol it may be in my head but it works for me