Announcement

Collapse
No announcement yet.

injection problems

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • injection problems

    I'm doing first cycle of test cyp 600 mg wk and EQ 500mg week. My problem is that I inject im in each side of glute of each aas once a week and where the injection site is it gets bump, brusing and sometimes itches. This will last until next shots. My glute are getting real sore, as they do not have enough time to heal before next wk.. can you help bro out? I have not used to injecting anywhere else.

  • #2
    sust golf ball bro.. inject slower and move to your legs.. you might be moving the dart too much..

    Comment


    • #3

      Comment


      • #4
        Here's a couple of suggestions:

        -Some people like to run the vial under some warm water first

        -make sure not to rotate the pin while it's in! This is common, don't forget what the end of the pin looks like, it's tearing your muscle if this happens!

        -make certain EVERYTHING is sterile! Wipe tops of vials and injection site thoroughly with alcohol!

        -give yourself plenty of time to inject, don't be rushed, or you'll more than likely try to puch the oil through the pin too quick as mentioned above!

        Here's a common one: IF YOU ARE SHOOTING IN THE GLUTES USE A 1.5" LENGTH NO MATTER HOW BAD YOU HAS THE NASSATOL (NO ASS) SYNDROME!!!

        The glute is a big muscle, even the smallest of booties need a 1.5" to ensure that the muscle is fully penetrated!
        leankid@ziplip.com

        Not around much more, because my job blows, but damn I miss you folks!!

        R.I.P. Geared Up, you are missed my friend!

        ***~LEAN~***

        Comment


        • #5
          Use your quads also, that will give you four injection sites. Thats plenty for what your doing.

          Comment


          • #6
            I love the delts! Take the shot and then workem out!!!! no pain no anything bad!
            PAIN IS ONLY WEAKNESS LEAVING THE BODY!


            O2BESOHUGE is the Queen of my life!

            "JESUS is LORD!"

            workin_hard99@yahoo.com

            Comment


            • #7
              ditto on being careful not to move the needle.

              also, you need to add delt and quad shots into the mix.

              Comment


              • #8
                Have a needle to go through the rubber stopper, this needle is only for extracting your oil. Now once you get all the oil you want, use a new needle before injecting. This menas your needle is sharp as can be. Just going through the rubber stopper on you vials will dull your needle. Never use a used needle on yourself.

                Comment


                • #9
                  If i do delts and quads do I still use a 1.5 inch needle? Oh, do I penetrate the full 1.5 inches into muscle? Doesn't seem there is enough depth for 1 1/2 inches in the delt.

                  Comment


                  • #10
                    Originally posted by mick-G
                    If i do delts and quads do I still use a 1.5 inch needle? Oh, do I penetrate the full 1.5 inches into muscle? Doesn't seem there is enough depth for 1 1/2 inches in the delt.
                    i use a 23g i inch and it does great
                    PAIN IS ONLY WEAKNESS LEAVING THE BODY!


                    O2BESOHUGE is the Queen of my life!

                    "JESUS is LORD!"

                    workin_hard99@yahoo.com

                    Comment


                    • #11
                      try 22g 1.5 in, goes in like butter

                      Comment


                      • #12
                        Rotate the spots

                        Here's some good info - check out the .zip file - might help you out with injecting.

                        RIP BigJim
                        RIP GU

                        www.x-2-o.com


                        J_Abbays@hushmail.com

                        Comment

                        Working...
                        X