MODS OR VETS...I fu**ed up

[pigmeat]

I just took my first shot of EQL test and EQ.The vials have the pop off caps wich i am not familiar with.My problem is i took the popoff and thering around side,thinking the stopper went into the neck of vial.IT DIDNT. IT just sits on top of vial.Now im fucked. Ant ideas? Can i just preload 19 syringeswith.5cc. ( THIS ONLY HAPPENED ON eq).dONT WANT TO CONTAMINATE GEAR!!!!HELP!

[nautica]

Don't preload. I would put it in the fridge and order some sterile viles from www.getpinz.com, you will have them in 3 days.

nautica

[pigmeat]

THANKS BRO! I am only familiar with the stoppers that go int the neck. I also thought the peel off ring was supposed to be taken off.

[trenboloni]

If I understood correctly, the inside of your vial is now exposed to air? If I were you, this is what I'd do:

1) Try to close the vial, use tape or whatever gets the vial as airtight as possible. Store in a cool, clean place.

2) Buy a .45 micron sterile filter and a few large (20ml syringes and empty vials (20ml).

3) Put the filter onto the 20ml syringe, put a needle on the filter but dont uncap the needle yet. "Open" the syringe by taking the plunger off, pour your eq in the syringe, put the plunger back on and inject the gear thru the filter into an empty sterile vial.

you will loose a few (2-3) ml's in the filter but the gear will be clean now. You can purge the filter with 2ml of sterile oil if you want.

I'm not sure where you can get filters as I live in Europe, but I think you could try the various fina kit dealers. Ask around, I know at least one of them has overnight shipping.

Hope it turns out good...

EDIT: Damn, I'm slow...

[pigmeat]

can i just heat the EQ to sterilize after putting in new vial?

[trenboloni]

Sure you can... but the question is, is it wise? You will kill bacteria but probably also degrade the hormone. I don't know how much it will degrade, i.e. will it lose two or twenty percent of it's potency. But if you cant get the filters, then heat it at 250 fahrenheits (dont quote me on that temp though, I know only the metric system...)

FYI, I have IP's test prop/suspension mix (200mg/ml) and it got too cold when it was mailed to me from China via airmail, and when I got it, it was full of crystals, actually it was more like oatmeal porridge than hormone suspended in oil. So basically I tried everything to "melt" the hormone back into the oil, and finally I had to pour 100ml of solution onto a steriled saucepan and boil it. It worked... and it seems that it's still as potent as it should be. So, the bottom line I guess is that bake it or filter it. I recommend filtering, but baking might be as good...?

[pigmeat]

thanks bro.I geuss i learned a valuable lesson.I have never seen a stopper like that.The test has a stopper that goes into vial.Pisses me off as it will probaply delay my next shot(thursday).Anybody else know about heating? I dont want to waste 2-3 ml,as i only have enough for 10 weeks.

[goliath.jr]

I would bake it if it were me, but that's just me.

[pigmeat]

what temp and for how long?

[Chemical Evolution]

Originally posted by pigmeat
can i just heat the EQ to sterilize after putting in new vial?

Dont heat your EQ you will most likely distroy it!


here's my melting point list:

nandrolone decanoate 39 c
boldenone undecylenate 77 c (?)
trenbolone acetate 97 c
test enanthate 39 c
test propionate 119 c

This is the temp where it all melts if you go a bit beyond that you risk destroying/Evaporating it!

[stripper]

u can get the whataman filters it is easy to use.

[jack hust]

that sucks bro sorry to hear about that

[Aragorn]

Sorry to hear about it...but listen to the guys on what to do but also listen to Chem.Evol. on not baking it. Good luck and for the future if you're not sure just check in with us

Aragorn