Finally!!!! Started Cycle Today 03-03-03

[teutonic]

TweetMy stats: 5'8 157 lbs. 28 yrs. old

I'm doing EQL Prop/Fina combo. I’ll be doing ½ cc ED. That’s 37 1/2 mgs of Fina and 50mg Prop ED for 8 weeks.

I have 60 Nolvadex tabs (20mg) and 60 Bromo tabs (2.5mg) on hand.

I’ll only start taking Nolvadex if signs of gyno appear. I’d start with 40mg first day, 20mg/day until symptoms subside, then 10mg/day for rest of cycle.

I’ll only start taking Bromo if signs of gyno appear. Take 1 pill (2.5mgs) a day split in half. Take 1/2 in the morning and the other half in the evening.

Liquid Clomid. I'll start taking this 3 days after last shot.

300mg day 1
100mg days 2-11
50mg days 12-21


Needles:

25G x 1 for the Chest, Biceps, Triceps, Delts, Calfs, Quads

23G x 1.5 for the Glutes


DAY 1

I had a tough time drawing the ½ cc from the vial. I used a 23G x 1.5 to draw with. Don’t know why I was having trouble. To make matters worse I weighed myself this morning and I am down a couple of pounds. (from 161 to 157). I was so depressed. What a way to start a cycle. But I just have to stay positive and not play mind games with myself. It’s my fault because I was slacking on my diet. Sorry for blabbing here. I’ll stop.

I’m very lucky to have my girl inject me but my first injection didn’t go well. I don’t know if I could inject myself. She injected me in the ass and I almost passed out. What a ***** I am. I got all light headed and flushed and felt like I was going to be sick. I had to go lay down for a couple of minutes. Five minutes later I felt better I ate and then went to the gym. Had a good workout. Just hope tomorrow’s injection goes better.

I’ll post using this thread to let you know how my cycle is going. I’ll use this as a little journal.

[rado]

TweetHope it goes well for you. BOh and by the way, when you draw from the bottle, you need to push air into it ok? That way it'll be easier for you to draw out of. Let's just say you want to draw 1cc, well you pull the plunger back 1cc then you push it in the bottle.

[Man Boobies]

TweetGood Luck with the cycle!!

Don't worry about the shots...you will grow to look forward to them!!!

Cheers,
MB

[rugbythug]

TweetI always draw with a 20 gauge and shoot with a 23. You dont want to draw and shoot with the same needle. A: easier to contaminate from stopper B: It gets dull.

[monstercojones]

Tweetgood luck bro... let me know how spot injects go, we're close to the same size.

[CJWolf]

Tweetcheers bro ... today was the big day for me too

[Massive1]

Tweetcongratulations bro

[teutonic]

TweetThanks all. I'll keep you posted.

Hey CJWolf good luck on your cycle

[CJWolf]

Tweet

Originally posted by teutonic
Thanks all. I'll keep you posted.

Hey CJWolf good luck on your cycle

I'm hoping for the best ... and better than hoping, i'm even eating right

[BiggKay]

Tweetbro on the drawing part...just heat up the vile with a blow dryer and it'll be a lot easier to draw it...thats what i do....hope it helps...

[jack hust]

Tweetgood luck bro looks good

[teutonic]

Tweet3/4/03


I have some questions. Hopefully you can help me out here. I know it looks like a lot but it really isn’t. If you can take some time I’d really appreciate it. Thanks

(1) When I did my first injection yesterday (in the glutes) it felt like I got a bruise. Today it is still hurting. The whole area is really sore but not discolored (just a slight hint of purple, like a dot) Did I fuck up??? Today’s shot it just feels slightly sore but much better than yesterday. Anything that can be done about this?

(2) I am having trouble drawing from the bottle. I’m using a 23G x 1 ½ needle to draw. I push a ½ cc of air into the vial but that still does not help. I guess its just to thick. Some have suggested heating up the bottle with boiling water or even a hair dryer but how would you go about doing it exactly? Also would doing this everyday fuck up the product? (I prepare my syringe the day before I shoot) If the solution is heating up the bottle to make it easier to draw from, would it make it that much easier to shoot also? Remember I prepare it the day before so would I have to heat the syringe some how to make it easier to shoot?


(3) When my girl injected me yesterday there was a little bit of juice left in the syringe(I used it for today’s injection). She pushed all the way in. Why would that be? It just wouldn’t go through.

(4) The same thing happened today. When she was finished injecting me, there was again a little bit of juice left in the syringe. But there was also some blood droplets in the syringe. Is this ok?

(5) Will I be able to use the juice that was left over in the syringe even though it had blood droplets in it? It seems like the blood droplets are not in the syringe now with the juice. It looks like its in the needle part where you twist it off the syringe and a drop in the tip of the needle.



Thanks again for any help.

[Double]

Tweethey bro there will always be a little bit of juice left over in the syringe. theres nothin u can do, unless u buy a cheap sterile oil or some b12 and draw that from the syringe first and then draw your juice. 25 gauge in my opinion is too small for what ur injecting. as for the bruise i would try icing it and keep an eye on it u don't want an infection.

[lord humongous]

TweetGet some 18g needles to draw with and you should have no problem.

[teutonic]

TweetDouble-- my last cycle I didn't have a problem with any juice being left over (EQ,Sus). As for the 25G being to small I dont want to shoot with a 23G into my Biceps, Triceps, Delts, Calfs or Quads. I think that might be to big.

lord humongous-- I dont want to use a 18G to draw because I think it will create to big of a hole and eventually when I turn the bottle upside down to draw from it the juice will drip out. Remember I am going to be punching 60 holes into the stopper.