Your way to draw from an AMP ?

[Deno]

TweetWhats your technique ?? I heard people like to snap the top off of an amp and take the plunger out of the syringe..then just put the oil from the amp in the syringe and then put the plunger back in../

[daved150]

Tweethuh...
that sounds waaaaay to stupid to me!! i just snap the top and draw it out...dam, i'm just thinking about that, and i'd have a whole new set of stories for y'all if i tried shyt like that!!! i'd have shyt EVERYWHERE!!! dig up my "test in the eye" story...you'll get the idea

[snickers1]

Tweet^bump

[kite]

Tweetjust snap the top and draw it up

[T-Man007]

TweetSnap and draw, that way no micro size pieces of glass get in your ass. Talk about a bad day, that would be a BAD DAY!

[O2BESOHUGE]

TweetI'D SAND THE SMALLEST PART OF THE AMP (WHERE ITS SUPPOSED TO CRACK) WITH A NAIL FILE ALL THE WAY AROUND FIRST...SNAPS CLEAN EVERY TIME

THEN USE A 1.5" NEEDLE TO DRAW IT OUT WITH

THIS IS HYPOTHETICALLY OF COURSE!! I DONT CONDONE THE USE OF STEROIDS WITHOUT A WRITTEN PRESCRIPTION FROM YOUR DOCTOR!!

O2

[MAK2102]

Tweet*For drawing from a vial:

***ALWAYS wash hands before injecting***

Wipe the top of the vial with an alcohol swab before the needle enters - do this every time you pull the bottle out from storage (do not blow on the top of the vial. Let the alcohol evaporate)

Pull back on the syringe approximately as much as you are going to fill it (i.e. - if you are going to draw one cc then first load one cc of air) poke the needle into the vial.

Inject the air into the bottle so that you have created a vacuum effect and drawing will be easier

*Pull back on the plunger until the desired amount is achieved (you may do this with the bottle upside down so that you can 'flick' the syringe to get the bubbles to settle while you are still in penetration.

*Once you have the amount you are looking for you will either (A). be ready to switch needles or (B). you may leave the needle on for pulling from another vial if you are going to mix

*So (A). you will pull back on the plunger once you are out of the vial to get the remaining liquid out from the drawing needle's base

*Poking the needle in to the vial dulls it. At this point you may want to switch to a fresh (sharp) needle.
You have now drawn from the vial.

[Rebel Yell]

TweetAs O2 had said.
File line and snap works best.
It's a BIIIOTCH when they crack.

[O2BESOHUGE]

Tweet

*For drawing from a vial:

***ALWAYS wash hands before injecting***

Wipe the top of the vial with an alcohol swab before the needle enters - do this every time you pull the bottle out from storage (do not blow on the top of the vial. Let the alcohol evaporate)

Pull back on the syringe approximately as much as you are going to fill it (i.e. - if you are going to draw one cc then first load one cc of air) poke the needle into the vial.

Inject the air into the bottle so that you have created a vacuum effect and drawing will be easier

*Pull back on the plunger until the desired amount is achieved (you may do this with the bottle upside down so that you can 'flick' the syringe to get the bubbles to settle while you are still in penetration.

*Once you have the amount you are looking for you will either (A). be ready to switch needles or (B). you may leave the needle on for pulling from another vial if you are going to mix

*So (A). you will pull back on the plunger once you are out of the vial to get the remaining liquid out from the drawing needle's base

*Poking the needle in to the vial dulls it. At this point you may want to switch to a fresh (sharp) needle.
You have now drawn from the vial.

MAK, HES TALKING ABOUT 1 ML GLASS AMPS BROTHER!! NOT MULTI-DOSE VIALS WITH RUBBER STOPPERS

O2

[MAK2102]

Tweethahahha yea i saw that after i posted. Of course I cant delete my post so i look like the village idiot on this one.

[O2BESOHUGE]

TweetNAAAAA...

[badasz32]

Tweeti take the amp and put the tip in the top of a bic pen cap. I snap it off then I draw it up with a 23g pin and switch to a 25g to stick with. I like to change needles because I always touch the pin against the glass trying to get it all out. I dont want to stick with a dull pin.

[JsJs24]

TweetSnap and draw with large gauge (21-22g). Then switch tips to whatever you prefer if nec. I also wrap toilet paper around the top of the amp when breaking it off.

[horsepwr]

Tweet2 key notes I noticed above;
1) Score around the neck of the amp, where it needs to break, with an emery board (nail file) for a clean break every time.
2. Draw with an inch-in-a-half tip and change needles before injection because the needle used to draw will be dull as hell.
(Large guage to draw, e.g. 20-21g for oils)

[Merc]

Tweetsnap and draw that way you dont get any glass in there


and mak you are the weakest link in this thread LOL