PLease help trouble injectin

[GetRipped]

Tweetok i injected before, but i went to do it about 2 min ago and i had the hardest time gettin the test into the syringe. it was like i was sucking but no liquid was going in the syringe. please help.

[rado]

Tweetpull back maybe about 2cc and push the air in the bottle, it'll help you out a bit. That way you create pressure within the bottle, easier to dispense.

[lord humongous]

TweetLike Rado said push some air in that should help. What size pin are you using to draw?

[Skarn]

TweetJust go real slow. It takes a good while depending on the size pin you are using. What size? My first cycle I used a 23g to draw with...took forever. Now I use an 18g to draw and switch to a 25g to shoot.

[34pumped]

Tweetyea do what rado said and the gauge of your needle probably neds to be changed

[rookie]

Tweetis the needle screwed all the way on the syringe? lol happend to me once .......... felt stupid

[GetRipped]

Tweetwait tht might be it wat do i have t do with the needl.. does it have to be a lil loose what you mean. because i think i tightened it all the way. sht thats probaby it. and also my ass is killin me. today was just a bad day

[rookie]

Tweetif it not tight it wont draw properly......sorry for the miss understanding. Your ass is kiiling? That could be a few things, what does the site look like? Is the a large welt? I got that once when i use a 1" 3ml gear in one site and i couldnt sit for a week, I think from what ive been reading here you should split 3 ml into two sites. Also the depth of the needle may cause a welt. I hope some one here can clear these symptoms up. A welt could also be an absess, and we don't want that, I think thats caused by dirt. I havnt use 1" since. I feel beter going deep. It sould be smoth going in, keep it straight less tearing. Im still learning myself, Im keeping it simple with 2x/week/sus250. Im now in my 5th week of a 10 week cycle.

[rookie]

TweetI know the depth of the needle wont cause the welt but the gear will if its not deep enough..............could be wrong here. Was wondering this for a while.

[rico]

TweetI would do what some others said to do. Push some air in ,use a diferent and larger gauge pin to draw with.Then switch to the pin you will use to inject. I find that drawing and shooting with the same pin is a little tough. It dulls the pin a bit.
About the pain and lump you have it might be from moving the pin a bit while you were injecting. You get better as you go. Also It depends what and how much you are injecting into a site. Just some ideas. Good luck bro.

[viav2000]

TweetBe patient when drawing - I use 23G for Fina and it takes a minute - pressurize the bottle like Rado said. Be sure you are going in deep enough. Plenty of info on here regarding what size pins to use for different spots. Take your time innjecting - I take a good 45 seconds or longer to get 1 ml of fina in. Do it right after a hot shower and massage the area. That should prevent welts for the most part. And NEVER foget to Aspirate!

[bigshug]

Tweetyes, what they said....I use 22g 1" to draw and 25 g 1 1/2" to inject.....

[bigdude]

TweetAll I have are 25g pins. Is it possible to draw test with that.

[viav2000]

Tweetare you injecting with the same pin you are using to draw with? You should be changing it out after you draw and before you poke yourself - go ahead and order some bigger needles for drawing. They are very cheap and if you go through some posts here you will find a source that will have them to you in 2 or 3 days.