carrier for liquids

What is a good carrier for oral liquids? For example tadal. I hate the taste of pure grain alcohol.
I do have some propylene glycol on hand.

Bump for a answer

You could use PEG (polyethylene glycol), And 151 rum, then get like cherry flavoring, or whatever you like. It won't be that bad at all bud. Everclear is terrible, But the 151 isn't to bad.

Thanks and another question. To make dbol oral what ratio of powder and liquid? Same question for tadal?

I would have to check. I will look through the stickys here, There may be something. If not I will find something.

By: H***** Balboner

There seems to be a lot of confusion on the boards how to prepare powders for oral use, it is actually quite simple here, this article contains some detailed directions, so you too can prepare your own powders for oral use.

A popular and easy method to make orally available hormones is by making a liquid solution. The directions you will find in this article will work for any orally available hormone such as winistrol, anavar, dinabol, anadrol, or any other hormone that is dosed in the MG/ML range. This will NOT work for something that is dosed in the MCG/ML range, such as clen or T3.

Points to consider

Pros:
• Quicker absorption into the body than a pill or capsule.
• Easier to accurately dose

Cons:
Not as convenient as pills or capsules • Strong taste

First thing is first, we will need to do a little math to determine the concentration that we require. Take the number of grams of your hormone powder, multiply by 1,000 to get the number of MG. Next take the amount per serving or ml you would like (i.e. 50mg/ml) and divide by your number of MG. This will give us the total amount of solution.

Example: 5 grams of anadrol powder, you want a solution of 50mg/ml. 5g x 1,000 = 5,000mg / 50 = 100.

Now that we know our total solution, we calculate for the room the powder will take up, as a rule of thumb for oral powders I use that each gram takes up 1ml (The actual amount of room 1 gram of powder takes up is .75ml, but this will slightly overdose your oral solutions, making them more effective). So our next step is total amount of solution, minus 1 for each gram of powder. This will solve how much total solvent we will need.

Example 100 – 5 (grams total) = 95

OK now we know how much solvent we need. As for a solvent, for oral solutions dosed in the MG/ML range (see chapter * for information on making oral solutions dosed in the MCG/ML range such as clen or T3.) I recommend using Everclear, yes the hard liquor, if everclear is not available in your state, try the highest proof grain alcohol you can find, usually Bircardi 151 will be the next best.

Alcohol is used as the solvent, because it will dissolve the powder much better than water, or any other liquid solutions. Don’t worry about the alcohol effecting liver values, 1 ml is your daily dose and it is a very small amount.

Step By Step Directions
Supplies One bottle of Everclear, or appropriate substitute. One sealable vial. One 18g pin. One 5ml or 10ml syringe.

Step 1 Place your powder in an appropriate sized vial.
Step 2 Using a syringe, preferably a 5ml or 10ml one, draw out your solvent.
Step 3 Put solvent in vial with powder. Be sure to keep up with the amount of solvent you have put in the vial, by writing it down on a sheet of paper to make sure you put the proper amount.
Step 4 Repeat step 2 & 3 until you have placed the total solvent amount into the vial.
Step 5 Shake and swirl the vial until all of the powder dissolves, heat if necessary.
Finished

Do The Math!

In this chart you will see for each desired mg/ml ratio, how much solvent to add per gram of powder to figure for more grams of powder, take the amount of solvent and multiply by the amount of grams.

1 gram powder

Desired MG/ML Ratio Add Xml Of Solvent
5mg/ml 199ml
10mg/ml 99ml
15mg/ml 65.5ml
20mg/ml 49ml
25mg/ml 39ml
30mg/ml 32.25ml
35mg/ml 27.5ml
40mg/ml 24ml
45mg/ml 21.25ml
50mg/ml 19ml
55mg/ml 17ml
60mg/ml 15.5ml
65mg/ml 15.25ml
70mg/ml 13.25ml
75mg/ml 12.25ml
80mg/ml 11.5
85mg/ml 10.75ml
90mg/ml 10ml
95mg/ml 9.5ml
100mg/ml 9ml



--------------------------------------------------------------------------------

Disclaimer: The articles and conversions posted are for entertainment and informational purposes only - experiment at you own risk.



Source: https://www.anasci.org/vB/anabolic-st...nversions.html

You should be able to figure the rest out. I would say use 10% PEG if you choose to use it with the 151.

That is awesome and thank you for the work you did on this. It takes all the guess work out of it. Your info really should be a stickie.

I cant take credit for it, but yea it makes it really easy. No problem bud that's what we are here for.