Tweeti used 22x1 fore my test and deca cyle but that was just in my ass and legs. I dont recomed it fore your arms and so on.
TweetI've been trying to figure out what size pins to use for my first test and deca cycle and i only found one thread that said that deca needed a 23g pin ...do you guys run deca with a 23g or is a 25 ok ???
thanks
Card
Tweeti used 22x1 fore my test and deca cyle but that was just in my ass and legs. I dont recomed it fore your arms and so on.
Tweeti plan on shooting in my glutes only. so you guys think 21 to draw and 23 to shoot ?? i was think about buying some 21g syringe and needles and some 23-25g pinz only ...does that the most efficent way to go ??
TweetIF YOUR GOING TO SHOOT IN YOUR GLUTES ALWAYS USE A 1'1/2 22G. FOR MY QUADS I USE A 23G 1'
Disclaimer: Steroid use is illegal in a vast number of countries around the world. This is not without reason. Steroids should only be used when prescribed by your doctor and under close supervision. Steroid use is not to be taken lightly and we do not in any way endorse or approve of illegal drug use. The information is provided on the same basis as all the other information on this site, as informational/entertainment value.
Please take the time to read these threads!
Fitness Geared Shoutbox rules
FG member signature rules
Fitness Geared Forum Rules
https://www.fitnessgeared.com/forum/f334/
https://www.fitnessgeared.com/forum/f283/
https://www.tgbsupplements.com/
TweetI shoot everything (water and oil) with a 25G Pin. Sure it shoots slow, but I got 30 or so seconds to kill, I don't need to get it done in 10.
Here's the most economical solution I have found:
1- Buy 3CC 21 or 22G syringe and pin combo. This is your drawing setup.
2- Also buy pins (pin only) in 25G in the following lengths
5/8" - Bi, Tri, Delt
1" - Quad, Calf
1.5" - Glute.
Unwrap, draw, switch pin to 25G, shoot. What can be easier?
TweetSame here, I use 25x 5/8 for everything and have never had a problem. The last 2 (or maybe 3 - they kind of run together) cycles were 12 and 15 weeks with ED shots (up to 2.5ccs) so if there was going to be a prob, i would have encountered it by now. I'm a ***** when it comes to needles so I could not deal with any bigger than 25g.Originally posted by gunz
I shoot everything (water and oil) with a 25G Pin. Sure it shoots slow, but I got 30 or so seconds to kill, I don't need to get it done in 10.
Here's the most economical solution I have found:
1- Buy 3CC 21 or 22G syringe and pin combo. This is your drawing setup.
2- Also buy pins (pin only) in 25G in the following lengths
5/8" - Bi, Tri, Delt
1" - Quad, Calf
1.5" - Glute.
Unwrap, draw, switch pin to 25G, shoot. What can be easier?
I use an 18g needle to preload all my pins (remove the 25g needle - stil inside the cover, fill syringe with the 18g sterile needle you just pulled from the bottle, then put the 25g back on - nothing to it.
TweetI use a 23g 1.5 pin in the glutes. Everybody has their own preference.
Tweeti will never go thicker than 25.. no need to. 25g 1" is the perfect size IMO. i use it on everything. no need to go 22g or 23g... why not minimize scar tissue?
Tweeti use 25 on everything, 1 and half in glutes, and 1 inche in bi, tricp, and shoulders
TweetI've never used anything smaller than 23 gauge and they are tough to push oil through. Its hard enough to give yourself a shot in the butt especially the first couple of times, so the larger the needle the easier and quicker it is.
TweetTrue...but my old lady is doing it, so i will have that on my side. i ordered 25g right now sooooo i guess i'll just trail and error it
Originally posted by medium1
I've never used anything smaller than 23 gauge and they are tough to push oil through. Its hard enough to give yourself a shot in the butt especially the first couple of times, so the larger the needle the easier and quicker it is.