Reply With QuoteTweetWhat brand is it bro?
Attention Guest, if you are not a member of Fitness Geared - Body Building & Fitness Community, you have 1 new private message waiting, to view it you must fill out this form.
Thanks: 0
Likes: 0
Dislikes: 0
FG Newbie 
test prop
TweetHas anyone ever had crystals form at the bottom of their bottle of test prop? Does this mean that it is bad or fake?
TweetWhat brand is it bro?
FG Newbie
TweetI am not sure what brand it is. It was sent in olive oil bottles so that it would not be seized when being mailed to me (the prop had a cloudy yellow look to it and had a white powder on the bottom). I was told to add BA to the solution 2ml of BA for every 50 mL of solution. I added the BA and baked it in the oven at 250 degrees for 15 minutes (3 times). The next day when I looked at the test prop it was a light gold color and it had the crystals in it. I am not a chemist, but is it possible that there was not enough BA in the test prop and that it did not completely bind with the prop.
VET
Tweetthats strange that your gear would be sent in olive oil bottles it would be impossible to keep sterile when you draw. it may be real but even if it is i would be damned apprehensive to order from that guy again. at best it is some basement homebrew propably is not even from powder. some guy doing syno conversions and sending it out. you could do that and do it right with the proper stuff that is easy to get and cheap.
"SHIAT BIOTCH, thats a big ass!"
A clear concience is a sign of a bad memory.
husband of the year
moose riding maple syrup drinking flanel wearing canuck wannabe
FG Newbie
TweetI took the prop out of the olive oil bottles and placed it in a vial with a rubber top (injected it into vial). I am pretty worried about how sterile the prop is. If you were to draw it out of a vial with out the rubber top, would it be similar to drawing something out of an amp with break off top (like sustanon 250 comes in) or would it be alot less sterile.
Established Resident
Tweetno...
the number one chinese dj in the whole mutha fukin world"dj tommy" from hongkong you all......
shout out to...hong kong bodybuilding association
VET
Tweeti would treat the oil as if its not sterile. i would start a new thread asking how to sterilize gear in the vial i have never done this so i cannot advise. you may also check the conversion forum there you will find what you need.
"SHIAT BIOTCH, thats a big ass!"
A clear concience is a sign of a bad memory.
husband of the year
moose riding maple syrup drinking flanel wearing canuck wannabe
TweetBad idea.
I would never inject that oil bro.
Definetely not sterile. Hope you dont get an infection shooting that stuff.
Established Member
TweetRun it through a whatman and bake it to sterelize. Add some BB to keep it suspended.
FG Newbie
TweetThanks for the information guys. I am just going to throw it out, it is not worth getting an infection.
TweetOriginally posted by MidnightRider
Run it through a whatman and bake it to sterelize. Add some BB to keep it suspended.
I agree.
Established Member
TweetThrow it my way, I'll put it to good use.Originally posted by HUGGERZ
Thanks for the information guys. I am just going to throw it out, it is not worth getting an infection.
FG Newbie
TweetI will give the whatman and BB a try before a throw it in the trash.
Established Member
TweetGood call bro.Originally posted by HUGGERZ
I will give the whatman and BB a try before a throw it in the trash.
Tweetprop needs alot of solvent( or PEG ) to keep from crashing ...... I'd heat in a boiling pot of water to see if it's just crashing ......if the crystals just dissapear then its crashing ....and will hurt when it crystalizes in your injection site.....( happened to me a few times ) in this case you will want to add a ml of PEG ( this will change the MG's so do the math . you should bake and filter it first with a .45 filter then a .2
then buy some b12 you may need it to cut the pain
Posting Permissions
